Replacing strings but one string in the set was the wrong size

Thanks for sharing Marco

@MarcoD96 the lesson here should be never cut your strings.

You can Donate used strings DONATE STRINGS — The Open String

2 Likes

Hi Marco,
And what a pity that this exception now happens with something as dull as a set of strings …you probably had just such a small chance at a big cash prize… if only you had bought a staatsloterij lot … :joy:(lottery ticket)
Greetings,Rogier

That site talks about strings for violins, cellos, etc. No mention of guitars.

As Justin says in his lesson always have a spare set just in case something goes wrong when replacing your strings.

Maybe this previous post on string recycling is of interest String Recycling

Another reason not to cut strings off. I just loosen them, take the string out from the bridge and unwrap the tuner post. Could always go back on in a pinch.

1 Like

I’ve never seen the point of cutting strings. Instead of 6 string ends to stab yourself with and scratch your guitar you now have 18! :weary:

Plus, I see videos of people cutting them while they are under tension! That could hurt you or your guitar. The tuners do turn both ways…

1 Like

Which brand of strings?

I loosen and cut my old strings for easy and fast removal. They get coiled up and then go in the trash. After that I put on new ones.

C’mon peeps. They are old guitar strings that have served their very important purpose and are no longer useful, they are not precious artifacts. Learn to let go. :slight_smile:

5 Likes

I find it easier not to cut them. It isn’t about hanging on to them. Cutting is an extra step that I don’t feel I need.

Steps if you cut:

  1. Loosen (lest it snap you or guitar)
  2. Cut
  3. Pop pins and remove ball end of string
  4. Unwind string fragment from post
  5. Coil long string scrap
  6. Coil short string scrap
  7. Get bandaids for fingers poked on 18 sharp sting ends.

Steps if you don’t cut:

  1. Loosen
  2. Pop pins and remove ball end of string
  3. Unwind other end from posts
  4. Coil intact string
  5. 1/3 chance of poking finger and needing bandaids.

See? Saved two steps and reduce my risk of damage to myself and guitar.

What is actually gained from cutting the strings?

Convince me!

2 Likes

I’m with CT, I cut them after untensioning. It’s faster. Particularly getting it off the tuning peg.

Doesn’t really matter if others decide they don’t want to cut though. Do what you want.

Seems unusual to get a wrong string in a pack. Unlucky there.

4 Likes

On a strat-type electric, the string is fed in from the back of the body, so the ball end is inside the body. To remove the string requires pushing the string back through the hole from the front to the back.

The part that was wrapped around the post is kinked up, making it difficult to push (or pull, however you want to look at it) through the hole.

Cutting the string somewhere in the middle gives me a straight wire on the ball end, which slides through that hole easily. I hope that makes sense.

4 Likes

Are you saying use a chainsaw?

1 Like

I cut the strings close to the saddle so there’s no short scrap to coil, just 6/12 little pieces to collect and throw out.

Also, anyone with a minimum of manual skills can easily avoid poking their fingers with the string ends. :slight_smile:

Having permanent eye shields is one of the few benefits of wearing glasses. (Well, that and seeing clearly)

3 Likes

This is sort of similar to how Tuno-o-matic bridges work.

I have a Strat too, but I still don’t cut the strings. I would think that anyone who plays guitar regularly has a string winder, no? It takes all of a few seconds to unwind all six strings enough to unwrap them from the peg and pull off. Then you pull the string through the body… you don’t push them.

I would agree that cutting the strings is “quicker”, but I don’t see why anyone would be in such an immense rush that a time saving of less than a minute is a critical factor. But each to their own.

I cut the strings on my strat. I’m impatient and I reckon unwinding them is a PITA.

I haven’t touched my electrics in so long, I forgot about how the strings threaded through.

I too would cut on those guitars, rather than pull the twisted end all the way through.

But, since only acoustics really matter :wink:….